ASTM A234 Gr. WPB ASME B16.9 Carbon Steel End Cap
The cap is a fitting that simplifies sealing pressure vessels or ends of pipes in a system. They are also referred to as pipe ends because an ASTM A234 WPB Cap is used at the extreme end of a pipe. Caps, when attached correctly provide a leak-proof sealing. While several industrial sectors use these fittings to seal pipes or pressure vessels. The ASTM A234 WPB Pipe Caps may also be used to eliminate the presence of air blocks in pipes, particularly in lines carrying water. Often, they are used to protect the ends of a pipe from getting deformed or chipped by external forces. Moreover, the use of a Butt Welding A234 WPB End Cap can prevent damage of internal threads inside the pipe or tube.
Product Information
| Product Name | ASTM A234 Gr. WPB ASME B16.9 Carbon Steel End Cap |
| Size Range | 1/2” to 48” |
| Wall Thickness | SGP STD SCH5S SCH10S SCH40S SCH 80S SCH160S XS XXS |
| Standards | ASTM A234 |
| Grade | WPB |
| Manufacturing Standards | ASME B16.9 MSS-SP-43 |
| Coating | Rust-proof black oil or hot galvanized, Transparent oil |
ASTM A234 WPB B16.9 End Cap Dimensions (mm)
The cap is used to seal an open end of the pipe. In piping engineering, the cap made in accordance with ASME B16.9 will be welded to the end and need not be included in the length dimension of the run of pipe.
| NPS | O.D
mm
inch | E [NOTE(1)]
mm
inch | E
mm
inch | E1 [NOTE(2)]
mm
inch |
| 1/2 | 21.3
0.84 | 25
1.00 | 4.57
0.18 | 25
1.00 |
| 3/4 | 26.7
1.05 | 25
1.00 | 3.81
0.15 | 25
1.00 |
| 1 | 33.4
1.32 | 38
1.50 | 4.57
0.18 | 38
1.50 |
| 1-1/4 | 42.2
1.66 | 38
1.50 | 4.83
0.19 | 38
1.50 |
| 1-1/2 | 48.3
1.90 | 38
1.50 | 5.08
0.20 | 38
1.50 |
| 2 | 60.3
2.38 | 38
1.50 | 5.59
0.22 | 44
1.75 |
| 2-1/2 | 73.0
2.88 | 38
1.50 | 7.00
0.28 | 51
2.00 |
| 3 | 88.9
3.50 | 51
2.00 | 7.62
0.30 | 64
2.50 |
| 3-1/2 | 101.6
4.00 | 64
2.50 | 8.13
0.32 | 76
3.00 |
| 4 | 114.3
4.50 | 64
2.50 | 8.64
0.34 | 76
3.00 |
| 5 | 141.3
5.56 | 76
3.00 | 9.65
0.38 | 89
3.50 |
| 6 | 168.3
6.62 | 89
3.50 | 10.92
0.43 | 102
4.00 |
| 8 | 219.1
8.62 | 102
4.00 | 12.70
0.50 | 127
5.00 |
| 10 | 273.0
10.75 | 127
5.00 | 12.70
0.50 | 152
6.00 |
| 12 | 323.8
12.75 | 152
6.00 | 12.70
0.50 | 178
7.00 |
| 14 | 355.6
14.00 | 165
6.00 | 12.70
0.50 | 191
7.50 |
| 16 | 406.4
16.00 | 178
7.00 | 12.70
0.50 | 203
8.00 |
| 18 | 457.0
18.00 | 203
8.00 | 12.70
0.50 | 229
9.00 |
| 20 | 508.0
20.00 | 229
9.00 | 12.70
0.50 | 254
10.00 |
| 22 | 559.0
22.00 | 254
10.00 | 12.70
0.50 | 254
10.00 |
| 24 | 610.0
24.00 | 267
10.50 | 12.70
0.50 | 305
12.00 |
| 26 | 660.0
26.00 | 267
10.50 | … | … |
| 28 | 711.0
28.00 | 267
10.50 | … | … |
| 30 | 762.0
30.00 | 267
10.50 | … | … |
| 32 | 813.0
32.00 | 267
10.50 | … | … |
| 34 | 864.0
34.00 | 267
10.50 | … | … |
| 36 | 914.0
36.00 | 267
10.50 | … | … |
| 38 | 965.0
38.00 | 305
12.00 | … | … |
| 40 | 1016.0
40.00 | 305
12.00 | … | … |
| 42 | 1067.0
42.00 | 305
12.00 | … | … |
| 44 | 1118.0
44.00 | 343
13.50 | … | … |
| 46 | 1168.0
46.00 | 343
13.50 | … | … |
| 48 | 1219.0
48.00 | 343
13.50 | … | … |
*NPS: Nominal Pipe Size; O.D: Outside Diameter at Bevel; E: Length [NOTE(1)]; E1: Limiting Wall Thickness for Length; E: Length[NOTE(2)].
ASTM A234 WPB CAP Chemical Compositions (%)
| Grade | C | Mn | P | S | Si | Cr | Mo | Ni | Cu | V | Nb |
| WPB | ≤0.30 | 0.29-1.60 | ≤0.050 | ≤0.058 | ≥0.10 | ≤0.40 | ≤0.15 | ≤0.40 | ≤0.40 | ≤0.08 | 0.02 |
*For ASTM A234 Gr. WPB, the carbon equivalent (C.E.), based on heat analysis and the following formula, shall be no greater than 0.50. C.E. = C + Mn / 6 + (Cr + Mo + V) / 5 + (Ni + Cu) / 15. The C.E. values shall be reported on the test report.
*ASTM A234 WPB fittings made from bar or plate may have 0.35 max carbon and that made from forgings may have 0.35 max carbon and 0.35 max silicon with no minimum.
*For each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum will be permitted, up to a maximum of 1.65%.
*The sum of copper, nickel, chromium, and molybdenum shall not exceed 1.00%
Product Tags:
|
|
Welded Carbon Steel Fittings End Cap ASTM A234 WPB ASME B16.9 Images
|
